Buy Low Price From Here Now
Precision drilling is a snap with the DELTA DP350 12-inch Variable Speed Bench Drill Press. This powerful drill press features variable speeds between 500 and 3,100 RPM for drilling a variety woods, plastics, and metals. The table easily adjusts 90 degrees to the left and right, and the table raising feature makes it a breeze to raise and lower. The standard three-jaw, 1/2 inch capacity chuck grips a wide variety of drill press cutting tools. Other convenient features include a three-spoke pilot wheel for easy operation, and a flexible lamp for added light while working.
Readmore
Technical Details
- Powerful 1/3 HP motor with variable speed capabilities of 500-3,100 RPM- Sturdy table adjusts 90 degrees to the left or right; rack-and-pinion depth adjustment allows for precise drilling
- Super sturdy cast-iron construction virtually eliminates vibration
- Measures 22 x 11 x 37 inches and weighs 78 pounds
- Includes 1/2-inch chuck key, belt and pulleys, and flexible lamp
See more technical details
By Gary L. Hopkins (Ft. Wayne, IN USA)
I should not have ignored all the poor reviews I found on several sites about the variable speed control on this drill press. I figured they had tried to adjust it when it wasn't running. I took delivery on this drill press yesterday. The very first time I turned it on and, SLOWLY AND GENTLY, tried to adjust the spindle speed. IT BROKE! When I opened it up, the belt had jumped the pulleys; it appeared as though the adjustable speed mechanism tore itself apart. I'll check into getting it fixed, but not sure I even want to keep it. That may depend on what the service people tell me about this piece of junk. At this point, though, it's a very heavy paper weight and definitely not worth wasting your time or money. This experience has SERIOUSLY damaged my opinion of the Delta brand.
By Lena Tordsdotter (Grafton, MA, USA)
I have had this drill press for almost 4 years for mostly light duty shop work. As my woodworking time is limited, it has not been used extensively. Despite this it has failed twice; first the on off switch broke down. It was fixable, but a bit annoying. Now the pin holding the spindle pulley broke, rendering the machine useless. It was not possible to get a part of the pin out, and I have temporarily fixed it with a piece of a coat hanger. It was disappointing to note that the accompanying parts diagram was rendering an incorrect picture of the machine, and it makes me question how much quality control this machine has been subject to.
When the coat hanger breaks I will invest in a Powermatic variable speed drill press, which might have been the right thing to do from the get go.
By Chosen One (Hilton, NY United States)
Good:
Variable speed - middle ranges are not marked but easy to figure out
Solid table
Solid three handle drill extension
Table crank works well
Fairly quiet
Bad:
Cheap chuck - upgrade to a Jacobs
Top motor pulley became seperated from collet - easy fix, drill hole through both when lined up, tap and then Loctite a screw to hold. Newer units have pins to prevent this, mine is 3 years old. Fix took 20 minutes.
Cover has too many screws - easy fix, remove screws and install a couple small hinges. Replace one screw on opposite with thumbscrew. Fix took 20 minutes.
Additional comment:
You do not need to lubricate this press or run through the speed range daily. Once a week would be fine. I service mine once a month.
By raziel
I purchased the Delta DP350 drill press from a service centre at a good price after reading the reviews at amazon. The drill press is refurbished and has a 2008 manufacture date. The pulley slippage design flaw mentioned by many reviewers was addressed and fixed by Delta in 2006. However, the decal still has only the 500 and 3100 speed ranges. I made a decal in AutoCad 2000 that I stuck over the existing decal and shows a range of speeds (See images). It would also help if Delta had addressed the issue of removing the six screws from top cover plate to lubricate the pulleys weekly. A hinge system would have helped. Other than that the drill press works great.
By Paula (California, USA)
After drilling about 300 holes in wood, the drill press started making a grinding noise and vibrating excessively. When I took it to the repair shop the technician told me it was probably the bearings. He commented that Delta uses cheap bearings made in China and they fail at a high rate. That was about a month ago. The repair shop had to send the press back to Delta and I haven't heard a word from anyone since.
While the press was working I was happy with it, except I would like a little more power for using hole saws on hardwood.
Images Product
Buy DELTA DP350 Shopmaster 1/3HP 12-Inch Bench Drill Press Now
0 Response for the "DELTA DP350 Shopmaster 1/3HP 12-Inch Bench Drill Press"
Post a Comment